Issue link: https://flip.summitcat.com/i/1440099
71 71 800.896.8665 WWW.RUNYONSURFACEPREP.COM Cement, Mixers & Overlays GROUT COATS & EPOXY JOINT FILL/REPAIR HUSQVARNA GM 3000 Formulated for re-grouting and hole filling in concrete surfaces. It's part of the HiPERFLOOR process. Effective for patching and filling small air pockets/pin holes when polishing. One gal. covers 200 to 300 square ft. 5 gal. covers 1,000 to 1,500 square ft. Item No. Description 543087161 1 gal. or 5 gal. CPS ARMOR GROUT KIT Developed to fill and repair concrete floor surface imperfections, such as air holes, popouts, surface pitting, scratches and gouges. Two- component, 95% solids structural polyurethane/polyurea hybrid. Coverage Rate: 435-875 sq/ft gallon. Available in 6 colors: Light Gray, Medium Gray, Dark Gray, Sand, Medium Brown and Dark Brown. Item No. Description GPCH0751 2 gal. or 10 gal. GROUT COATS AMERIPOLISH PG-7K POLISHABLE GROUT COATING SYSTEM Fast setting, polymer modified, high-strength cement with great bond strength formulated to fill in small cracks, pinholes and surface irregularities. Increases durability, gloss and distinction of image (DOI). PG-7K accepts Ameripolish concrete dyes and requires no special polishing procedures. Ameripolish PG-7K Part A - Powder must be used with PG-7K Part B - Liquid. Item No. Description PG-7K 50 lb. Part A, 2.5 gal. Part B METZGER/MCGUIRE MM-80P EPOXY JOINT FILLER Two-component, 100% solids content epoxy joint filler. When cured, semi-rigid (hard but slightly resilient) filler with a Shore hardness of A90-95. Developed to fill and protect joints in industrial concrete floors that are subject to hard wheeled material handling traffic and heavy loads. Supports traffic and protect joint edges from spalling. Should be installed full joint depth in saw-cut control joints (or 2'' min. in joints where depth exceeds 2'') per PCA and ACI guidelines. In construction (formed) joints that are not saw-cut, should be installed 2'' deep. If shrinkage crack is excessive and needs to be ''choked off,'' it may be sealed with dry silica sand. Designed for use where final temperatures are from 40F (10C) to +120F (49C). Item No. Description MM80-P-SG-10 10 gal. Kit, Gray METZGER/MCGUIRE ARMOR-HARD CONCRETE EPOXY KIT W/AGGREGATE A two-component, 100% solids epoxy with early set properties. Developed specifically for the repair of industrial concrete floors to handle intense traffic. Use with sand aggregate creates a trowelable mortar and then can also be used as a liquid for some repairs. Typical Uses: As a mortar it can do spall repairs/rebuilding of joint shoulders, as a topping for delaminated slabs, fill in holes, gouges, ruts, pop outs, and repair broken slab panel corners. As a liquid, it fills wider random cracks and bonds concrete to itself. Color of the blended epoxy is translucent/clear. Mortar color will be the color of the aggregate. Limitations: DO NOT use in joints or cracks that move, as a surface coating, and for deep repairs install in max 1'' (25 mm) deep layers to avoid shrinkage due to exotherm. It should be installed at or higher than 50°F (10°C). Pedestrian/construction traffic in 3-4 hours, Grinding/sanding in 3-4 hours, Hard-wheeled traffic in 8 hours or less, At 70°F it does not require separate primer, USDA/FDA acceptable, Superior impact, abrasion and chemical resistance, very low odor. Item No. Description AHLV-PART-A-1 1 gal. MMAHK-D 5 gal., Dorian Gray, Dovetail Gray, Standard Gray MMAH-1 1 gal., Dovetail Gray, Natural/Clear, Porpoise, Standard Gray EPOXY JOINT FILL/REPAIR METZGER/MCGUIRE MM-80 EPOXY JOINT FILLER MM-80 is a 100% solids, two component, heavy duty semi-rigid epoxy joint filler designed to fill and protect contraction and construction joints in industrial concrete floors. 5:1 ratio, used primarily for manual dispensing. Developed to fill and protect joints in industrial concrete floors that are subject to hard wheeled material handling traffic and heavy loads. Final temperatures are from 40°F (10°C) to +120°F (49°C). It is also ideal for joint and crack repair. ALL COLORS but Standard Gray must be ordered in quantities of FOUR. Item No. Description MMM8-CC-1 1 gal. or 10 gal., Multiple Colors